Did you know?

Press "reset" each time the waste drawer is emptied. If you are still having trouble following the previously mentioned troubleshooting steps, please complete these additional steps: Clean any waste from the globe. Remove the waste drawer. Run a clean cycle with the drawer removed. 4. Reply.Use only the power supply provided with the unit. Litter-Robot consumes a very small amount of power: When the motor is working to rotate the globe during a clean cycle, Litter-Robot uses just 2.7 watts of electricity. When Litter-Robot is on standby, which is 99% of the time, it uses just 0.36 watts of electricity.My litter robot keeps turning in the wrong direction for a clean cycle. After I perform a hard reset multiple times, it will occasionally do a normal cycle and return home with a normal solid blue light and it will function normally for a short while but it will once again start to turn the wrong way for about 30 degrees and return back to the ...Ensure the globe is on the track and lock the black key on the back of the globe into the pocket. Replace the bonnet, ensuring all 4 tabs are secured. Press the 'Power' button to turn the unit back ON. **The globe will not rotate and the yellow light will blink if the issue is due to the bonnet connection.1. Remove the bonnet and globe from your existing Litter-Robot 3. 2. Place the globe on the new base, making sure it's straight and in the tracks. 3. Place the bonnet on the new base by inserting the bonnet tabs into the rear bonnet slots, then press the latches while rotating it forward, until the latches click into place. 4.Make cat-life easier with Litter-Robot 4, the newest, quietest, and smartest automatic litter box for cats. Litter-Robot 4 features advanced litter-sifting technology, reduced litter tracking, and real-time monitoring of waste and litter levels through the Whisker app. The elegant design and wide opening maximizes comfort for cats of all sizes.While performing maintenance on your car, you may disconnect the radio from the battery in your GM vehicle. GM cars contain Delco radios that are protected by Theftlock, which lock...How to reboot your Litter-Robot to help with onboarding the Whisker App on your Litter-Robot. Follow our step-by-step guide for a hard reset.Get the most out of your automatic litter box with the latest Litter-Robot 3 manual. Learn more about Litter-Robot 3 setup, lights, troubleshooting, and more.Why does my Litter-Robot stop mid-cycle? If your Litter-Robot 3 stops mid-cycle, check out this helpful troubleshooting video to help remedy the problem. We’...Litter-Robot 3: Filling the Globe. Fill the Globe through the opening with clumping litter until it meets the raised Fill Line when spread flat (about 8-10 pounds by weight or 1 gallon by volume). Be careful not to overfill the Globe. Then press the Reset button. Litter-Robot's litter sifting system requires clumping litter to work properly.Unplug the power supply from the back of the base. Wait 1 minute. Plug it back in. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty ...A self-cleaning litter box like Litter-Robot eliminates the need for pet parents to have to scoop, saving time and frustration brought on by an unpleasant chore. Additional benefits include better managing odor control, keeping cats' paws cleaner, and helping reduce litter usage.The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won't leave the globe or by too much weight in the unit, the timing light will flash red. You will also receive a notification on your phone if you ...Introducing your cat to Litter-Robot. Most likely, your cat will quickly adapt to Litter-Robot. When using in automatic mode, be sure your cat or kitten weighs at least 3 lbs—the weight scale will not recognize cats weighing less than 3 lbs. ... Reset. Press and release the Reset button to zero the weight scale. (Do this after emptying the ...The app drawer % is always wrong. All day the % on mine goes up and down regardless of my cats using it. Clean the sensors then and see if that helps. why did they remove the reset option in the app? We have a new litter robot 4. We just emptied it for the first time. We hit the reset button several times, but the app still shows that it’s 95 ...Litter-Robot 4: Red Light Bar Momentary Flash (Control Panel Lockout Mode) Litter-Robot 4: Red Light Bar with Partial White Flashing (Globe Position) Litter-Robot 4: Red Ping-Pong Light Bar (Motion in Drawer) Litter-Robot 4: Red with Partial Yellow Flashing (Over-torque Fault) Litter-Robot 4: Sensors and Functions.Here are the procedures you can do to fix the over-torque issue: 1. Reboot Your Litter-Robot. Sometimes, the Litter-Robot might just be acting up, so try rebooting the device. Empty the globe by removing the litter, then press the reset button on the robot.

If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful. If your unit is not displaying a solid blue light after ...If your Litter-Robot 3 is not powering on, there are several things we need to check. Ensure Litter-Robot is plugged directly into a wall outlet. We do not recommend using an extension cord or power strip. Unplug the power supply from the wall. Confirm that your outlet is working by testing it with a known working device, such as a lamp or cell ...The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to. There's a lot of dust and debris which can cause issues, which leads to the robot not ...These biodegradable liners are made specifically for the Litter-Robot, but any 10-13-gallon trash bag will also work. Open a new liner or bag. Roll down the edge about four times. Starting at the back, push the edge of the bag into each of the four tabs, keeping the bag taut as you work forward.

Vacuum the inside perimeter of the bezel with a brush attachment, passing over the holes at the top of the bezel where the curtain sensors are located. Now, let's run a test cycle. Short press the Reset button, then short press the Cycle button to run a Clean cycle. After Litter-Robot cycles, it should return to the Home position, displaying a ...Hi My 2 year old robot litter tray (thank God I bought the 5 year warranty) is not very happy. I have (yet again) had drawer sensor issues and suspect that it, again, needs a replacement sensor as the full light is just continuously flashing. I have turned it off for periods of time before turning it on again, the sensor clear plastic guards are clean, the tray bag is not sticking up and yes I ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Phone and Chat support available Mon-Fri. Possible cause: Discover how to troubleshoot issues related to the bonnet removal on your Litte.